Vapor Barrier vs. Vapor Retarder: What to Use
Use a vapor barrier only in specific cold-climate or below-grade assemblies; for most retrofits, a Class II or III vapor retarder is safer, and some assemblies need no added vapor-control layer at all. Get the choice wrong and you can trap moisture, feed mold, rot framing, and weaken insulation. This guide covers perm ratings, code classes, and project-by-project choices for walls, basements, crawl spaces, attics, and slabs.
| Decision factor | Vapor barrier | vapor retarder | Winner |
|---|---|---|---|
| Moisture resistance | Blocks vapor diffusion movement and is typically 0.1 perm or less | Slows diffusion but still allows some vapor transmission | Vapor barrier |
| Drying potential in wall and roof assemblies | Lowest drying potential if placed on the wrong side or used with another low-perm layer | Usually preserves more drying room for a cavity or roof deck | vapor retarder |
| Best-fit retrofit use | Below-grade walls and under-slab work | Above-grade walls, mixed-climate retrofits, and many insulated roof assemblies | vapor retarder |
| Risk when installed wrong | Higher risk of trapped moisture in above-grade walls | Lower risk when matched to assembly and climate | vapor retarder |
What is the difference between a vapor barrier and a vapor retarder?
A vapor barrier blocks vapor diffusion much more than a vapor retarder does. A vapor retarder still slows moisture movement, but it leaves more drying potential in the assembly. That matters because walls, roofs, and floors need a way to dry after seasonal humidity swings or small leaks.

Builders and manufacturers use the terms loosely, so the perm rating is the number that matters. Lower perm means less vapor passes through. Fine Homebuilding says these layers slow moisture diffusion through roof, wall, and floor assemblies, while builders are urged to focus on air leaks first.
Perm ratings and vapor-control classes
The IRC defines a vapor retarder as a vapor-resistant material with a perm rating of 1 or less. In practice, that often covers Class I and Class II materials, while Class III materials are more open and are commonly used where some drying is needed. Exact ratings come from manufacturer data.
| Class | Perm range | Common examples | Typical role |
|---|---|---|---|
| Class I | 0.1 perm or less | Polyethylene film, glass, sheet metal, foil-faced insulated sheathing, nonperforated aluminum foil | Highest resistance to vapor diffusion |
| Class II | 0.1 perm to 1 perm | Unfaced expanded polystyrene, fiber-faced polyisocyanurate, asphalt-backed kraft paper facing on fiberglass batt insulation | Common choice where some drying room is still needed |
| Class III | 1 perm to 10 perms | Latex paints over gypsum board, #30 building paper, plywood | Light vapor control with more drying potential |
How to read manufacturer data instead of guessing
Do not buy by material name alone. Check the label or data sheet for perm rating, facing type, and where the product belongs in the assembly. That last point matters because the same material can be fine in one location and a mistake in another.
Suppose you are finishing a basement wall in a mixed climate and the packaging says “foil-faced” with a low perm rating. That may be correct on the warm-in-winter side in one assembly, but it can become a problem if another low-perm layer already exists on the opposite side.
Vapor barrier vs. vapor retarder at a glance
The main trade-off is simple: a vapor barrier gives stronger vapor resistance, while a vapor retarder usually gives more drying room. For many above-grade projects, that extra drying room is the safer choice because the goal is control, not total shutdown of vapor movement.
Where each material belongs
Vapor barriers are sometimes used in basements around foundation walls and under slabs. Benjamin Obdyke notes that they are rare in above-ground wall systems. Vapor retarders are far more common in typical wall and roof assemblies because those assemblies still need a path to dry.
Why above-grade walls usually need drying room
Above-grade walls face seasonal swings, incidental wetting, and the chance of small air leaks. If both sides of a cavity are low-perm, moisture has nowhere to go. That is how a wrong layer traps moisture and leads to decay in wood framing or lower insulation performance.
Vapor-control materials homeowners will see
Product names can hide the real class. Polyethylene film and foil-faced products often fall into the low-perm group, while kraft facings, latex paint, plywood, and certain building papers may land in Class II or Class III depending on the exact product data.
What to confirm on the label before you buy
- Confirm the perm rating on the manufacturer data sheet.
- Check whether the facing is foil, paper, plastic film, or none.
- Verify the intended location in the assembly: interior side, exterior side, under slab, or against foundation walls.
- Look for installation notes about seams, laps, and compatible layers.
A common first-timer mistake is to treat “plastic sheet” as a universal answer. A 6-mil poly sheet may be appropriate in one below-grade detail and wrong in an above-grade wall that already has a foil-faced board or other low-perm exterior sheathing.
Vapor-control decision matrix
Use the assembly, climate, and drying direction to decide. The right choice is not the same for a basement, a crawl space, an attic, an exterior wall, or a slab. Below is a homeowner matrix for the five retrofit scenarios that come up most often.

| Scenario | Recommended approach | Warning signs | What to verify |
|---|---|---|---|
| Unfinished basement | Use a vapor barrier on the foundation side when the detail calls for it; otherwise use a code-approved retarder or no added layer if the assembly already controls moisture | Visible dampness, efflorescence, or a second low-perm layer already on the wall | Perm rating, whether the layer belongs against concrete, and whether another barrier already exists |
| Conditioned crawl space | Use vapor barrier details on the crawl floor and foundation walls where the assembly is designed for it; keep the space air-sealed and conditioned | Standing water, open vents left in place, or a humid crawl space with wood showing staining | Perm rating, seam treatment, and exact location in the crawl-space assembly |
| Attic retrofit | Use a vapor retarder or no added vapor-control layer, depending on climate and roof assembly; do not default to a barrier | Roof leaks, mixed layers already in the roof, or a cold roof deck with poor drying potential | Facing type, perm rating, and whether the roof assembly can dry inward or outward |
| Exterior wall renovation | Usually use a vapor retarder or vapor-open interior finish; avoid adding a true barrier in above-grade walls unless the design calls for it | Existing foil-faced insulation, vinyl wallpaper, or multiple low-perm layers in the cavity | Perm rating of each layer, existing wall buildup, and local code requirements |
| Slab-on-grade | Use a true vapor barrier or under-slab vapor protection when the slab detail requires it | Dark spots, musty flooring above the slab, or a missing under-slab membrane | Product rating, ASTM E1745 reference where required, and placement under the slab |
When should you use a vapor barrier?
Use a vapor barrier when the assembly is below grade, under a slab, or specifically detailed to stop moisture movement at the concrete interface. The same source notes these products are sometimes used around foundation walls and under slabs. In above-grade walls, a true barrier is rarely the default choice.
Below-grade and under-slab conditions
Concrete can move a significant amount of moisture, so slab details may need under-slab vapor protection. That is why under-slab vapor protection is one of the clearest places where the term vapor barrier comes up, and why slab details often point to a product standard such as ASTM E1745. The barrier belongs where the concrete detail needs it, not wherever “more protection” sounds better.
Warning signs that a barrier would create a drying problem
If a wall already has a low-perm exterior layer, or if the interior finish is also low-perm, adding another barrier can trap water. That risk is higher in mixed climates, where seasonal direction changes and a cavity may need to dry inward part of the year and outward at another time.
Choose vapor barrier if… / Choose vapor retarder if…
Choose the stronger barrier only when the assembly is designed for it and the moisture path is clear. Choose the retarder when you need control without blocking all drying. For many homeowner retrofits, the safer answer is a retarder or no added layer at all.

Choose vapor barrier if…
Choose Vapor barrier if the work is under a slab, on a foundation wall detail that calls for one, or in another below-grade assembly where the goal is to stop diffusion through concrete or soil-facing surfaces. Choose it only when the product label, placement, and local requirements all point the same way.
Choose vapor retarder if…
Choose vapor retarder if you are insulating an above-grade wall, retrofitting an attic, or working in a mixed or humid climate where the assembly still needs drying potential. Choose it when the data sheet shows a Class II or Class III product and the wall can dry at least one direction.
Choose neither if…
Choose neither when the assembly already has an appropriate control layer, or when the first job is air sealing and drainage rather than adding another vapor layer. In older homes, that is common. A hidden barrier can create a double-barrier condition that traps moisture instead of solving it.
Is air sealing more important than vapor control?
Yes, in most retrofits air sealing comes first. The same source notes that builders are urged to focus on sealing air leaks rather than worrying too much about vapor diffusion. Air movement carries far more moisture than diffusion, so a tight air barrier often does more for durability than an extra vapor layer.
How air barriers and vapor control differ
An air barrier stops air movement through the assembly. A vapor barrier or retarder slows vapor diffusion. Those are different mechanisms, and a material may do one, both, or neither. Do not assume that taped foam, polyethylene, or foil solves every moisture path.
What to seal before you add insulation or a vapor layer
- Seal rim joists, penetrations, and framing gaps.
- Fix bulk water entry before insulating basement or crawl-space walls.
- Check roof leaks and flashing before adding attic insulation.
- Confirm the existing wall layers so you do not add a second low-perm layer by mistake.
Say your 1940s exterior wall already has foil-faced board on the exterior and you add interior polyethylene during a remodel. That creates a low-drying cavity on both sides. If the wall ever gets wet from a small leak, it has very little chance to dry.
Frequently asked questions
Do I need a vapor barrier or a vapor retarder in my walls?
Most above-grade walls do better with a vapor retarder, not a true barrier, and some wall assemblies need no added layer at all. The right answer depends on climate, siding, sheathing, and whether the wall can dry inward or outward. Check local code and the full wall stack-up.
Is 6-mil plastic a vapor barrier or a vapor retarder?
Six-mil plastic is commonly treated as a vapor barrier because polyethylene film is a Class I material and can be 0.1 perm or less. That does not make it right for every wall. It is often a better fit for below-grade or under-slab work than for typical above-grade walls.
When should you use a vapor barrier instead of a vapor retarder?
Use a vapor barrier when the assembly is below grade, under a slab, or specifically designed to stop moisture movement through a concrete-related detail. In above-grade walls, a barrier is rarely the first choice because it can reduce drying potential and create trapped moisture if the wall ever gets wet.
What perm rating counts as a vapor barrier?
A material with a perm rating of 0.1 or less is generally treated as a vapor barrier. The IRC defines a vapor retarder at 1 perm or less, but the very low end of that range is what most people mean by a true barrier. Always check manufacturer data for the exact rating.
Can the wrong vapor barrier trap moisture in a wall?
Yes. If you place a low-perm layer on the wrong side of the assembly, or add one on both sides of an older wall, the cavity may not dry. That can lead to decay, mold, and insulation that performs poorly because it stays damp.
Do vapor retarders allow walls to dry out?
Yes, more than vapor barriers do. That is the point of Class II and Class III products: they slow diffusion without shutting down drying entirely. The exact drying potential still depends on the whole assembly, including exterior sheathing, interior finish, and climate.
What materials are Class I, Class II, and Class III vapor retarders?
Class I includes polyethylene film, glass, sheet metal, foil-faced insulated sheathing, and nonperforated aluminum foil. Class II includes unfaced expanded polystyrene and fiber-faced polyisocyanurate. Class III includes latex paints over gypsum board, #30 building paper, and plywood. The label matters more than the generic material name.
Sponsored / affiliate links. As an Amazon Associate I earn from qualifying purchases. I may earn additional commission from eligible campaigns.

